|
ASSEMBLY (Labor only, no machining) |
|
|
Assemble Shortblock, Stock Motor |
$50 |
|
Assemble Shortblock, Race Motor |
$100 |
|
Assemble Complete Engine, Stock Motor |
$100 |
|
Assemble Complete Engine, Race Motor |
$175 |
|
|
|
|
BLOCK
WORK (Honing, Boring, etc) |
|
|
Deck Block |
$50 |
|
Rough Hone Block with Torque Plate,
Sunnen |
$25 |
|
Finish Hone |
$25 |
|
Full Hone (Sunnen, Ball, and plateau)
with torque plate |
$60 |
|
Clearance for Cam |
$25 |
|
Clean Block |
$25 |
|
|
|
|
CARB WORK |
|
|
Flowbench Carb (QMA) |
$20 |
|
Bore Carb & rework Circuitry |
$50 |
|
Max Bore Carb & Rework Circuitry |
$60 |
|
Install Throttle Wheel |
$20 |
|
|
|
|
CAMSHAFTS |
|
|
Grind Cam |
$70 |
|
Weld and Grind Cam |
$135 |
|
Degree Cam |
$25 |
|
Degree & "Twist" Cam |
$75 |
|
|
|
|
CRANKSHAFTS |
|
|
Grind Crank |
$50 |
|
Weld Crank |
$60 |
|
Stroke Crank |
$110 |
|
Cut Crank for Bearing |
$50 |
|
|
|
|
CONNECTING RODS |
|
|
Race Prep Stock Rod |
$30 |
|
Cut Rod for bearing |
$50 |
|
Media Blast Rod |
$10 |
|
|
|
|
CYLINDER HEAD |
|
|
Mill Head |
$25 |
|
Angle Mill Head |
$35 |
|
Cut Spring Pockets |
$25 |
|
Assemble Head |
$25 |
|
Install intake and exhaust valve guides |
$10 per guide |
|
CC Chamber |
$10 |
|
CC Chamber to Spec (including machining) |
$60 |
|
Surface head to put back factory type
machining marks |
$25 |
|
|
|
|
DYNO
SERVICES |
|
|
DYNO ENGINE (3 Pulls minimum) |
$40 |
|
DYNO TUNE ENGINE, QMA |
$50 |
|
DYNO TUNE ENGINE, ASN |
$50 |
|
DYNO TUNE ENGINE, RACE ENGINES |
Call |
|
|
|
|
REBUILDS, STOCK MOTORS |
|
|
Rebuild Stock Engine, labor only |
$100 |
|
|
|
|
REBUILDS, ASN MOTORS |
$200 |
|
Rebuild ASN engine, labor only |
$250 |
|
|
|
|
REBUILDS, RACE MOTORS |
|
|
Rebuild Race engine, labor only |
$200 |
|
|
|
|
REBUILDS, QUARTER MIDGETS |
|
|
Rebuild QMA Engine to Stage 3 Specs,
labor, basic parts, and dyno |
$300 |
|
Reassemble motor after teardown |
$75 |
|
Check Engine to QMA Specs (no assembly) |
$125 |
|
Check Engine to QMA Specs (with
assembly) |
$200 |
|
|
|
|
VALVE WORK |
|
|
3 Angle Valve Job |
$25 |
|
Single Angle Valve Job (QMA) |
$20 |
|
Install 27.5mm Valve |
$25 |
|
Install 28.5mm Valve |
$75 |
|
Back Cut Valves |
$10 |
|
|
|
|
OTHER ENGINE WORK |
|
|
HELI-COIL STRIPPED HOLES |
$10 |
|
WELDING |
BY THE HOUR |
|
LATHE WORK |
BY THE HOUR |
|
TUBE BENDING AND FABRICATION |
BY THE HOUR |
|
EQUIPMENT REPAIRS NOT LISTED ABOVE |
BY THE HOUR |
|
CC ASN Motor |
$40 |
|
CC ASN Motor & Set to spec |
$75 |
|
|
|
|
EQUIPMENT LIST |
|
|
Mill with DRO |
|
|
Lathe with DRO |
|
|
Surface Grinder |
|
|
Sunnen Bore Hone |
|
|
Superflow Flow Bench |
|
|
Dyno, torque arm w/performance trends
data system. |
|
|
Band Saw |
|
|
Bench Grinder |
|
|
20 Ton Press |
|
|
Media Blast Cabinet |
|
|
Drill press |
|
|
Ultrasonic Cleaner |
|
|
Media Tumbler |
|
|
Miller MIG Weldler |
|
|
|
